Podolsk,
14 Lobacheva st.
To contact page
RU EN
Tue-Fri 11:00-20:00
Sat-Sun 11:00-17:00
Mon - Closed

Crankcase Ventilation

Modifying the crankcase ventilation is a very popular modification among stunt riders. There is a lot of information about it online, including contradictory information. On the same motorcycles people use different setups with varying success.

The problem

The problem is that, along with crankcase gases, oil from the crankcase gets into the air filter box. As a result the motorcycle starts smoking (white smoke from the muffler), and hydrolock is also possible when enough oil gets into the combustion chamber. Since oil is incompressible, the connecting rods can bend when the pistons hit the oil layer. This effect shows up when riding on the rear wheel for a long time and is made worse by heavily overfilling the oil to fight oil starvation. This problem affects many sport bikes, but to different degrees. Before making changes, it is advisable to make sure the problem actually exists. To do this, remove the tank –> disconnect the crankcase ventilation hoses from the air filter box –> check whether there is oil in the hoses and how much.

If the hoses are dry, obviously no oil is coming through them and nothing needs to be done. If they are oily, open the air filter box and check for oil inside. If there is a greasy oil film, or worse, oil, then the crankcase ventilation needs to be modified.

The goal

The goal is to keep oil from getting into the air filter box without disrupting crankcase ventilation. There can be many options.

The solution

  1. Disconnect the crankcase ventilation pipes from the air filter box and cap them with a pod filter. Be sure to seal the corresponding holes in the air filter box airtight. If only small amounts of oil are being thrown, this setup will work fine. In theory you don't even need the filter, since there is no vacuum in the crankcase (only pressure), and it can't suck air in through the hose, only blow out.
  2. Disconnect the crankcase ventilation pipes from the air filter box and route them into a container, which must not be airtight, since it needs to be open to the atmosphere to vent the gases. Be sure to seal the corresponding holes in the air filter box airtight. The size of the container depends on how much oil is thrown: the more oil, the bigger the container. With this setup you need to monitor the amount of oil in the container and empty it periodically.
  3. Fit an oil catch can (oil separator) into the hose between the breather and the air filter box. With this setup the injectors keep drawing in the gases. Drain the collected oil back into the crankcase through the ventilation hole if there is no check valve or, if there is one, through the filler neck, by making a hole in the filler cap. This setup is suitable if a lot of oil is thrown and it's too tedious to constantly monitor the level in a container and top up the oil in the crankcase as the level drops. The catch can separates the oil. This way cleaned crankcase gas goes into the filter box, and the oil drains back into the crankcase.

Implementation on a 2005 Yamaha R6

The R6 doesn't suffer from oil starvation; most riders don't even overfill the oil. It's considered enough to fill the oil to the maximum. So the crankcase ventilation problem isn't acute for this motorcycle. Oil can be thrown during long rides at 12 o'clock or past the balance point. To be sure the engine is protected, it's better to make this modification. The ideal option is to fit an oil separator (catch can). A catch can is a very primitive device: a container with two holes. Crankcase gases together with oil enter the catch can through one hole, the oil condenses on the walls, and the cleaned gases exit through the other hole. For better oil condensation you can stuff a household metal scouring pad, the kind used to clean burnt residue off frying pans, inside the catch can :) Fitting the catch can requires removing the tank. The task is to fit the catch can between holes 1 (crankcase) and 2 (air filter).

The problem with fitting a catch can on the R6 is that there is very little space under the tank. The Chinese-made unit shown in the photo is at the size limit and only just fits. Such a catch can can be tucked under the wiring between the crankcase and the injector unit. The green dotted line in the photo shows where the catch can sits. Next, connect holes 1 to 3 and 2 to 4. It's important not to kink the hose; for this it's best to use a reinforced hose and route it without tension. You also need to position the catch can holes correctly relative to each other so that in a wheelie the accumulated oil doesn't get into hole 4 and through it into the air filter. The catch can is installed. If oil gets into it, it will stay there; it's best to take it out and check it at the end of the season. This way we managed to route the crankcase gases (with oil) away from the air filter without disrupting crankcase ventilation.

Note

Beginners who can't ride a wheelie for at least a minute don't need to overfill the oil or modify the crankcase ventilation.

Recommend
Stunt Riding World Champion Foma Magazine Ouest Bike Show 2023 Best Harley Sportster Stunts Magazine Relay for LED Turn Signals